29.03.2024

Irbis Dingo T 150, snowmobile parts

Spare parts for the Irbis Dingo T150 are high-quality, they justify their price. I rarely change them when the service period comes. I liked the machine itself, it can be transported in the trunk of a car, but a rubber mat is required, because the snow sticks and melts quickly.

In general, the device is good. If you still don’t have enough money for a big snowmobile, but you want to ride, then this is the best option

Even the best snowmobiles require regular diagnosis and repair. In the following sections, catalogs of certified spare parts from manufacturers for Irbis Dingo T150 are collected. You can be sure of the quality of components if you use original parts for repair.

Spare parts catalog

The catalog offers spare parts for the Dingo T150 model. When choosing products, pay attention to the fact that the year and model match the information on the website and the data of the technical passport of the snowmobile. If when choosing products there are doubts about the conformity of the model, then you need to consult a specialist.

There are various spare parts and ready-made kits for the Dingo snowmobile:

  1. Timing piston and crankshaft Part 1
  2. Timing Part 2
  3. Cooling system
  4. Carter
  5. Gearbox
  6. Starter
  7. Variable speed drive
  8. Engine
  9. Muffler
  10. Body parts
  11. Electrician
  12. Chassis with controls

Specialists are ready to advise the client on the choice of spare parts for Dingo. The consultation is completely free.

What to consider when working with the directory:

  • All products that are indicated on the diagrams are available individually, unless otherwise noted. For example, a scheme with a piston-cylinder group includes two elements: a piston (PS) and its rings (K). If these parts are framed in the frame to which the number is given, this means that the goods are delivered in a set, i.e. PS goes with K. If each of the elements has a unique number indicated on the diagram, then the goods are delivered individually.
  • Be careful when choosing products that have a dimension or color. Elements of the power unit (engine) Irbis Dingo T 150, including various colors, are displayed schematically under their number. But in the list of elements they are presented under different numbers. If it was not possible to determine the characteristics of the desired part, then you need to contact the specialists of the site.
  • The motors are delivered in a complete set that corresponds to the catalog number in 2 elements: short block and assembly unit.

The complete set of the selected item must be clarified by a specialist by calling the phone number listed on the site. You can also contact by email or online.

Piston, crankshaft

The main elements of the gas distribution mechanism of the first part are the crankshaft and piston system on the Dingo T 150. Pay attention to the prices (C) of the parts.

Details
  • tensioner shoe complete with chain stabilizer (2 pieces) – 294 rubles;
  • drive circuit – 229;
  • crankshaft – 4248;
  • chain tensioner – 180;
  • guide bush (10 pieces) – 409;
  • cylinder head – 2204;
  • K piston – 195;
  • piston – 475;
  • gaskets of the cylinder-piston group (CPG) in the set (3 pieces) -97;
  • CPG with K, gaskets, bushings, piston – 1545.
Cost

A set of CPG with additional spare parts will cost 5973 rubles.

The cost of the elements (separately) for the piston and crankshaft in total can amount to 8331 rubles

In more detail products with a unique number are presented in the figure.

T150 dingo pistons are manufactured according to manufacturers’ specifications, and they can be sold complete with parts such as: K, fingers and snap rings. All parts are interchangeable with original products.

Piston Installation Features

First you need to accurately understand the cause of the breakdown of the previous part and eliminate it. If repair is not possible, it is recommended to buy a new CPG and make a replacement. But remember that this may not solve the problem if it is not clear what caused the problem.

Measure the cylinder. If its dimensions exceed 0.07 mm, then it needs to be bored into a new size, and the nicosilic one needs to be replaced or covered with an iron sleeve.

Attention! Before installing the piston rings on the piston, check the clearance in their locks.

Use a special tool to install the snap rings! Do not fit screwdriver, pliers, hammer. They lead to a change in the shape of the product and breakage. Take a good look at the position of locking K in the ditch. It should sit entirely in the groove.

Timing 2 H

The second part of the gas distribution mechanism should include spare parts:

  • rocker arms timing belt (2pcs) – 214;
  • gas distribution mechanism cracker – 51;
  • two valve springs – external and internal – 150;
  • valve stem seals (2 pcs) – 92;
  • valves (kit, pair) – 246;
  • camshaft – 745;
  • gas hose meter – 113;
  • benzofilter – 48;
  • valve cover – 445;
  • cap ring – 92;
  • rocker arm – 306;
  • camshaft cover – 478;
  • cylinder head – 2204;
  • cylinder-piston gaskets (3 pieces) – 97;
  • guide bush – 409;
  • carburetor spacer – 104;
  • adjusting screw with nut – 49;
  • valve spring – 75;
  • hairpins – 45;
  • intake manifold – 229-402.

As a result, the cost of timing products of the second part can be from 6102 to 6275 p.

The spare parts for the timing, which are presented in the catalog, are created at the factories of company companies and are of good quality, as evidenced by user reviews. Original products from Taiwan and other countries are produced using proven technologies and new equipment.

Cooling system

It is recommended that regular device diagnostics be performed. If the cooling system malfunctions, it may be necessary to replace products.

Find out the Ts (in rubles) and the complete set:

  • cooling fan – 144;
  • a casing for the fan – 197;
  • decorative lattice – 156;
  • cylinder cooling casings – 287;
  • oil cooler – 3519;
  • filter – 575;
  • radiator hose – 1520.

Total, the price of all elements of the cooling system (CO) Irbis T150 is 6398 p.

Check out how the products in the picture look:

Cooling system repair

Before buying spare parts, it is advisable to find out how to properly repair the cooling system.

Cooling system diagram

Necessary actions:

  1. Withdrawal. To facilitate further disassembly, remove the fan impeller nut
  2. Remove the starter (manual), disconnect the four-pin connector between the base of two devices – the base of the mardino and the switch. Disconnect the tips of the spark plugs and the fan housing (HV) in the kit.
  3. Cleaning. Rinse products in solvent.
  4. How to disassemble and assemble. Remove the fan inlet 11. To remove and install the impeller nut 10, install the impeller with a stopper. During assembly, the nut tightening force should be up to 50 N / m.
  5. How to adjust the belt tension (PH) of a fan. The deflection of the VN 12 belt from a force of 5 kg applied in the central part between the pulleys should be up to 9 mm.

To adjust the tension, you need to add or remove K adjusting 8 between the pulley 7, 9. Install the other adjustment rings between K spacer 6 and half of the pulley 7 (from the housing). Adjust unused rings. To remove the bearing from the fan housing, apply force to the inner race of the bearing 5 using a punch. Washers must be stored for later assembly.

Remove retaining ring 6 and heal the second bearing (PN). To install, insert one PN in place and install K retainer with washers. After that, do the same with the second one on the other side of the fan casing 13. Press in so that the bearing is flush with the casing. Press the fan shaft from the motor side into the fan housing. Look for free rotation. During assembly, grease the threads of screw 1. The gaskets must be placed on both sides of the inlet and outlet openings 2, 3, then install the air intake 11.

On a snowmobile with a liquid-cooled engine, to drain the coolant from the system, you need to pump it out of the expansion tank. To do this, it is better to use a hand pump with a sleeve installed deep in the expansion tank. If the coolant level is low, raise the rear half of the vehicle to drain the coolant from the radiators.

Carter

The adaptation of the mechanism protecting the device from damage and pollution should contain the following products (the price is indicated in rubles):

  • sleeve – 409;
  • case housing right – 2382;
  • Starter – 1445;
  • motor gaskets set – 447;
  • studs m8x195 – 171;
  • crankcase housing left – 5901;
  • studs m8x187 – 168;
  • engine silent block (2 pcs) – 138 + 138;
  • crankshaft oil seal – 141;
  • cover of the crankcase of the left – 362;
  • K sealing – 174.

The cost of all Irbis T150 crankcase instruments is 11,876 rubles.

Starter

The working period of the starter is relatively short, so sometimes the device needs to be changed.

Damage may occur unexpectedly, replacement may be required. Find out how expensive it will cost.

The starter contains different spare parts (indicated in rubles):

  • key – 49;
  • coupling – 1629;
  • bearing – 126;
  • laying of a cover of a case – 108;
  • crankshaft oil seal – 141;
  • cover of the right engine crankcase – 1247;
  • generator stator – 1698;
  • generator rotor – 1187;
  • cooling fan – 144;
  • guide bush – 409;
  • drive circuit – 144;
  • spring – 99;
  • cork (2 pcs) – 97;
  • hall sensor – 98;
  • pump – 244;
  • gear – 445;
  • probe – 97;
  • filter – 48.

As a result, the cost of the starter device will be 8010 p.

The starter is an important part of the device, which is used to start the power unit. If it fails, you can try to start the engine “from the pusher”. But it is difficult to do it yourself, especially if the weather is frosty. Therefore, it is better to buy a starter.

Variable speed drive

CVT is important in transmission. We learn about the main components that are included in the device:

  • CVT assembly, rear – 2100;
  • payment – 750;
  • drum – 395;
  • bearing – 56;
  • engine gaskets – 447;
  • CVT cover – 4277;
  • cup – 832;
  • outer pulley – 348;
  • front variator bushing – 142;
  • CVT front – 979;
  • gliders – 97;
  • rollers (6 pcs) – 198;
  • guide bush – 409;
  • variator belt – 345.

Most often you have to change the driving pulleys in case of their mismatch and beating. The cost of products for the variator, together with the device itself, will be 9275 p.

Gearbox

The device is designed to work in tandem with the engine. Prices of parts included in the gearbox (in the river):

  • gear shift sensor – 458;
  • bearing (2 pcs.) – 56;
  • lever plate – 460;
  • indicator needle – 250;
  • lever tip – 232;
  • cork bolt – 165;
  • lever axis – 580;
  • oil seals (2 pcs.) – 48 + 48 + 118;
  • rings (2 pcs.) – 24 + 45;
  • engine silencer – 138;
  • needle bearing – 515;
  • gearshift shaft (copy) – 1525;
  • open bearing (2 pcs) – 100 + 59;
  • fork – 803;
  • gear lever – 1062;
  • gearbox shaft – 3212;
  • sleeve – 409.

The total price of the gearbox components will total 10307.

Body parts

During operation, the owner of the Irbis Dingo T150 may need to change the following components:

  • dashboard – 3690;
  • fairings: front, top, side – 684 + 1064 + 1017 + 1023;
  • mounting bolt – 200;
  • ignition switch – 400;
  • manual bolt -275;
  • lighthouse – 1700.

The cost of body components will be 10,053 rubles.

For clarity, the elements are presented in the figure below:

Additionally, the cigarette lighter and handle heating button are included in the category of body components. Their cost will be 1200 p.

Running

If the owner has been operating the Irbis T150 snowmobile for a long period of time, it may be necessary to replace the following chassis components (prices are indicated in the river):

  1. clamp – 400.
  2. steering wheel – 587.
  3. shaft – 879.
  4. handlebars – 1469.
  5. gas control lever – 2023.
  6. gas cable – 186.
  7. rear disc brake – 2868.
  8. suspension arm bush – 170.
  9. steering wheel mount – 158.
  10. switch block – 91.
  11. rear brake lever (disc) – 375.
  12. brake machine – 947.
  13. armored hose – 539.
  14. support – 1052.
  15. pads – 366.

The cost of the elements of the chassis of the snowmobile will be 12112 rubles. Before buying, make sure that it is impossible to repair the faulty component.

Electrician

Over time, the Irbis T150 snowmobile speedometer starts to show incorrect values ​​or completely stops working. Repair can take a lot of time, so it’s better to buy a new device.

We suggest you learn more about it and other components of electronics (price in p.):

  • control panel – 3690;
  • ignition switch – 385;
  • button to turn on the heating of the steering wheel grips – 445;
  • cigarette lighter – 564;
  • handles for a snowmobile – 1500;
  • gas lever – 2050;
  • switch block – 913;
  • speedometer sensor – 776;
  • rear lamp – 751;
  • temperature measurement sensor – 800;
  • starting concentrator – 385;
  • Starter – 1445;
  • starter relay – 684;
  • switchboard – 458;
  • starter relay – 334;
  • gear shift sensor – 458;
  • ignition coil – 764;
  • tourniquet – 364;
  • fuse – 15;
  • health indicator – 506;
  • voltage regulating relay – 989;
  • fuse box with two fuses – 114.

For all components of Irbis T150 electronics, the owner will spend an average of 18390.

Fuel system

Owners identify damage to fuel hoses on their snowmobiles due to the natural wear of the material. Often it makes no sense to repair them, but you can replace them. We offer you to find out about the price of a hose and other spare parts of the fuel system (TS):

Vehicle Components Price
Benzofilter 48
Fuel level sensor 262
Tank cap 304
Gas hose 113
Fuel tank 2000
Fuel valve 344
Start-up concentrator 400
Resistance filter 244
Carburetor 3834
Intake manifold 230
Engine

We recommend buying the power unit assembly. It is more economical. So you can install it faster.

Engine spare parts assembly, their prices and final cost for everything:

  1. Engine Assembly – 36000;
  2. Silencer – 2213;
  3. Filter – 575;
  4. The filter of zero resistance – 244;
  5. Radiator – 3520;
  6. Filter zero resistance 2 pieces – 845;
  7. Additional spare part in the engine – 242.

Cost for all 43539 p.

Muffler

This snowmobile device has an internal packing of materials with a high degree of sound absorption. It is important to take care of modernization deliberately because of the loss of the possibility of heat transfer to the outside. If there is a malfunction, it is recommended to buy a new muffler from the manufacturer.

Prices in rubles and the cost of all muffler elements:

  • bracket – 200;
  • silencer – 2213;
  • gasket – 47.

The cost of all parts amounted to 2460 p.

What is the average price of spare parts for Irbis Dingo T150 on the Internet and in the market

Depending on the type of device, the cost varies. We offer you to get acquainted with the elements and their prices in rubles:

  • silencer – 2460;
  • engine – 43539;
  • fuel system – 7779;
  • electrician – 18390;
  • running gear – 12112;
  • body parts – 10053;
  • gearbox – 10037;
  • CVT – 9275;
  • Starter – 8010;
  • sump – 11876;
  • cooling system – 6398;
  • piston, crankshaft – 7000;
  • timing belt – 6200.

The final cost of the Irbis T150 elements is affected by: the number of spare parts of the device, manufacturer and manufacturing material.

Leave a Reply

Your email address will not be published. Required fields are marked *